From: Bjorn Helgaas This can be disabled with "floppy=no_acpi", which should only be required if your BIOS supplies incorrect ACPI _CRS information about I/O ports, IRQs, or DMA channels. Signed-off-by: Bjorn Helgaas Signed-off-by: Andrew Morton --- 25-akpm/Documentation/floppy.txt | 6 + 25-akpm/drivers/block/floppy.c | 183 +++++++++++++++++++++++++++++++++++++++ 2 files changed, 189 insertions(+) diff -puN Documentation/floppy.txt~add-acpi-based-floppy-controller-enumeration Documentation/floppy.txt --- 25/Documentation/floppy.txt~add-acpi-based-floppy-controller-enumeration 2004-11-11 01:19:18.835616160 -0800 +++ 25-akpm/Documentation/floppy.txt 2004-11-11 01:19:18.840615400 -0800 @@ -204,6 +204,12 @@ in /etc/modprobe.conf. It's been recommended that take about 1/4 of the default speed in some more extreme cases." + floppy=no_acpi + Don't enumerate floppy controllers using ACPI namespace. + You may need this if your ACPI is buggy and doesn't report + a floppy controller when it actually exists, or if it + reports incorrect I/O port, IRQ, or DMA information. + Supporting utilities and additional documentation: ================================================== diff -puN drivers/block/floppy.c~add-acpi-based-floppy-controller-enumeration drivers/block/floppy.c --- 25/drivers/block/floppy.c~add-acpi-based-floppy-controller-enumeration 2004-11-11 01:19:18.837615856 -0800 +++ 25-akpm/drivers/block/floppy.c 2004-11-11 01:31:30.094447920 -0800 @@ -181,6 +181,13 @@ static int print_unex = 1; #include #include /* for invalidate_buffers() */ +#ifdef CONFIG_ACPI +#include +#include + +static int no_acpi_floppy; +#endif + /* * PS/2 floppies have much slower step rates than regular floppies. * It's been recommended that take about 1/4 of the default speed @@ -4150,6 +4157,9 @@ static struct param_table { {"slow", NULL, &slow_floppy, 1, 0}, {"unexpected_interrupts", NULL, &print_unex, 1, 0}, {"no_unexpected_interrupts", NULL, &print_unex, 0, 0}, +#ifdef CONFIG_ACPI + {"no_acpi", NULL, &no_acpi_floppy, 1, 0}, +#endif {"L40SX", NULL, &print_unex, 0, 0} EXTRA_FLOPPY_PARAMS @@ -4222,11 +4232,180 @@ static struct kobject *floppy_find(dev_t return get_disk(disks[drive]); } +#ifdef CONFIG_ACPI +static int acpi_floppy_registered; +static int acpi_floppies; + +struct region { + unsigned int base; + unsigned int size; +}; + +struct floppy_resources { + unsigned int nr_io_regions; + struct region io_region[2]; + unsigned int irq; + unsigned int dma_channel; +}; + +static acpi_status acpi_floppy_resource(struct acpi_resource *res, void *data) +{ + struct floppy_resources *fd = (struct floppy_resources *) data; + struct acpi_resource_io *io; + struct acpi_resource_irq *irq; + struct acpi_resource_ext_irq *ext_irq; + struct acpi_resource_dma *dma; + int n; + + if (res->id == ACPI_RSTYPE_IO) { + io = &res->data.io; + if (io->range_length) { + n = fd->nr_io_regions; + if (n < 2) { + fd->io_region[n].base = io->min_base_address; + fd->io_region[n].size = io->range_length; + fd->nr_io_regions++; + } else { + printk(KERN_WARNING "%s: ignoring I/O port region 0x%x-0x%x\n", + DEVICE_NAME, io->min_base_address, + io->min_base_address + io->range_length - 1); + } + } + } else if (res->id == ACPI_RSTYPE_IRQ) { + irq = &res->data.irq; + if (irq->number_of_interrupts > 0) + fd->irq = acpi_register_gsi(irq->interrupts[0], + irq->edge_level, irq->active_high_low); + } else if (res->id == ACPI_RSTYPE_EXT_IRQ) { + ext_irq = &res->data.extended_irq; + if (ext_irq->number_of_interrupts > 0) + fd->irq = acpi_register_gsi(ext_irq->interrupts[0], + ext_irq->edge_level, ext_irq->active_high_low); + } else if (res->id == ACPI_RSTYPE_DMA) { + dma = &res->data.dma; + if (dma->number_of_channels > 0) + fd->dma_channel = dma->channels[0]; + } + return AE_OK; +} + +static int acpi_floppy_add(struct acpi_device *device) +{ + struct floppy_resources fd; + acpi_status status; + unsigned int base, dcr; + + memset(&fd, 0, sizeof(fd)); + status = acpi_walk_resources(device->handle, METHOD_NAME__CRS, + acpi_floppy_resource, &fd); + if (ACPI_FAILURE(status)) + return -ENODEV; + + strncpy(acpi_device_name(device), "Floppy Controller", + sizeof(acpi_device_name(device))); + printk("ACPI: %s [%s] at I/O 0x%x-0x%x", + acpi_device_name(device), acpi_device_bid(device), + fd.io_region[0].base, + fd.io_region[0].base + fd.io_region[0].size - 1); + if (fd.nr_io_regions > 1) { + if (fd.io_region[1].size == 1) + printk(", 0x%x", fd.io_region[1].base); + else + printk(", 0x%x-0x%x", fd.io_region[1].base, + fd.io_region[1].base + fd.io_region[1].size - 1); + } + printk(" irq %d dma channel %d\n", fd.irq, fd.dma_channel); + + /* + * The most correct resource description is probably of the form + * 0x3f2-0x3f5, 0x3f7 + * Those are the only ports this driver actually uses. + * + * 0x3f0 and 0x3f1 were apparently used on PS/2 systems (though + * this driver doesn't touch them), and 0x3f6 is used by IDE. + * Some BIOS's erroneously include those ports, or omit 0x3f7, + * so we should also be able to handle the following: + * 0x3f0-0x3f5 + * 0x3f0-0x3f5, 0x3f7 + * 0x3f0-0x3f7 + * 0x3f2-0x3f7 + */ + base = fd.io_region[0].base & ~0x7; + dcr = base + 7; + +#define contains(region, port) ((region).base <= (port) && \ + (port) < (region).base + (region).size) + + if (!(contains(fd.io_region[0], dcr) || contains(fd.io_region[1], dcr))) { + printk(KERN_WARNING "ACPI: [%s] doesn't declare FD_DCR; also claiming 0x%x\n", + acpi_device_bid(device), dcr); + } + +#undef contains + + if (acpi_floppies == 0) { + FDC1 = base; + FLOPPY_IRQ = fd.irq; + FLOPPY_DMA = fd.dma_channel; + } else if (acpi_floppies == 1) { + FDC2 = base; + if (fd.irq != FLOPPY_IRQ || fd.dma_channel != FLOPPY_DMA) + printk(KERN_WARNING "%s: different IRQ/DMA info for [%s]; may not work\n", + DEVICE_NAME, acpi_device_bid(device)); + } else { + printk(KERN_ERR "%s: only 2 controllers supported; [%s] ignored\n", + DEVICE_NAME, acpi_device_bid(device)); + return -ENODEV; + } + + acpi_floppies++; + return 0; +} + +static struct acpi_driver acpi_floppy_driver = { + .name = "floppy", + .ids = "PNP0700", + .ops = { + .add = acpi_floppy_add, + }, +}; + +static int acpi_floppy_init(void) +{ + int err; + + if (no_acpi_floppy) { + printk("%s: ACPI detection disabled\n", DEVICE_NAME); + return -ENODEV; + } + err = acpi_bus_register_driver(&acpi_floppy_driver); + if (err >= 0) + acpi_floppy_registered = 1; + return err; +} + +static void acpi_floppy_exit(void) +{ + if (acpi_floppy_registered) { + acpi_bus_unregister_driver(&acpi_floppy_driver); + acpi_floppy_registered = 0; + } +} +#else +static inline int acpi_floppy_init(void) { return -ENODEV; } +static inline void acpi_floppy_exit(void) { } +#endif + int __init floppy_init(void) { int i, unit, drive; int err, dr; + if (acpi_floppy_init() == 0) { + err = -ENODEV; + goto out_put_acpi; + } + raw_cmd = NULL; for (dr = 0; dr < N_DRIVE; dr++) { @@ -4411,6 +4590,8 @@ out_put_disk: del_timer(&motor_off_timer[dr]); put_disk(disks[dr]); } +out_put_acpi: + acpi_floppy_exit(); return err; } @@ -4627,6 +4808,8 @@ void cleanup_module(void) /* eject disk, if any */ fd_eject(0); + acpi_floppy_exit(); + wait_for_completion(&device_release); } _